Laser cutting machine specific operation process is as follows: 1, abide by the general cutting machine safety operation procedures.
In strict accordance with the laser launcher to start the laser.
2, the operator must be trained, familiar with equipment structure, performance, and master the knowledge about operating system.
3, wear labor protection articles according to the rules in the vicinity of a laser beam must wear protective glasses in keeping with the rules.
4, in can not ascertain whether a particular material with laser or before heating, not to its processing, in order to avoid potential danger of smoke and steam.
5, the operator shall not leave the job or when the device is passed to tube, if indeed need should be shut down or cut off the power switch when they leave.
6, will put a fire extinguisher readily accessible place;
When not in processing to switch off the laser or light brake;
Don't place in the vicinity of without protective laser paper, cloth or other combustible materials.
7, in the machining process of abnormal, should immediately stop, timely troubleshooting or report to the competent personnel.
8, keep the laser, the lathe bed and the surrounding site neat, orderly, no oil, artifacts, plank, waste stack according to regulations.
9, the use of the cylinders, should avoid to crush the welding wire, so as to avoid leakage accidents.
The use of gas cylinders, transportation shall comply with the rules of the cylinder.
Ban cylinder blasting bask in the sun or away from heat.
When you start the cylinder valves, the operator must stand in the bottle mouth side.
To abide by high pressure safety procedures for servicing.
40 hours per operation or maintenance, each work 1000 hours a week or maintenance every six months, to be carried out in accordance with the rules and procedures.
Boot should be manually after the X, Y direction to start the machine tool at low speed, check with or without abnormal situation.
For new workpiece after the input process, should first test run, and check the running status.
Pay attention to the machine running situation at work, in order to avoid cutting machine out of the valid range or two collision accident.
Laser cutting machine is the laser will be emitted from a laser, the optical path system, focus on high power density of laser beam.
Laser beam to the surface of workpiece, the workpiece to achieve or boiling point, melting point and high pressure gas and beam coaxial will melt or gasification metal blown away.
As the movement of the relative position between the beam and workpiece, eventually to form material slitting, so as to achieve the goal of cutting.
Laser cutting processing is not visible beam instead of the traditional mechanical blade, with high accuracy, fast cutting, cutting pattern is not limited to restrictions, automatic typesetting save materials, incision smooth, low processing cost etc, will gradually improve or replace the traditional metal cutting processing equipment.
The mechanical part of the laser cutting head and the workpiece out of contact, no scratches on the workpiece surface at work;
Laser cutting speed, incision smooth level off, generally no subsequent processing;
Cutting heat affected zone is small, plate deformation is small, narrow kerf width,
No mechanical stress, with no shear burr;
High machining precision, good repeatability, does not damage the material surface;
CNC programming, can be processing any plan, wide big whole board can be cut, do not need to open mold, economic time.
Metal laser cutting equipment recommendation: preferential deals offer 4007001618 【
Metal laser cutting equipment 】
It is mainly used for cutting stainless steel, carbon steel, aluminum, copper, aluminum, iron, gold, silver etc. Thickness is 1.
0 ~ 25 mm plate;
Stainless steel laser cutting equipment 】
Classic gantry double drive structure of stable and reliable, automatic switching table, at the same time of cutting up and down on another table, convenient and quick to save time;
Optical fiber laser cutting 】
With high-speed movement speed, acceleration and dynamic performance, is laser for efficient and specialized research and development of a product, its cutting 0.
The speed of 5 mm stainless steel reached 100 m/min.
Carbon steel sheet metal laser cutting 】
Specializing in sheet metal processing industry demand for sheet of processing in the field of research and development design of laser processing equipment, it has a very high cost performance, with CNC system control, efficiency is much higher than in other laser cutting equipment for the board drive mode control.
Laser cutting machine laser cutting more laser metal cutting equipment